Basis Informatie.
Aantal Switch
Dubbele Schakelaar
Structuur
Vermogen Ingebouwd Type
Gebruik
Bedieningsknop, Resetknop, Schakelaar
Soort
Enkelpolige aan-uit schakelaar
Detectie methode
Retro-reflectieve modus
Size
115(L)*70(W)*44(H)mm
Range
Mini 30m Line of Sight
Maximum Loads
500W, 2-Gang 400W or 3-Gang 300W Incandescent /150
Operating Temperature Range
32-104° F (0-40° C)
Use Environment
for Indoor Use Only
Z-Wave Frequency
908.42MHz
Specificatie
Rohs, SGS, UL, FCC
Oorsprong
Dongguan, China
Beschrijving
ZW31T In-wall Wireless Smart Switch,DimmerIntroductionThe Wall Mounted Switch is a component of the lighting control system.Wire the Wall Mounted Switch in place of a standard wall switch.Inclusion of this Switch allows remote ON/OFF control of loads connected.This Wall Mounted Switch is designed to work with otherZ-Wave enabled devices.Z-Wave nodes of other types can be added to the system and will also act as repeaters.Technical data
Operating Voltage | 120Vac/60Hz |
Maximum Load | 500W, 2-gang 400W or 3-gang 300W incandescent /150W CFL/LED |
Powered by | Z-wave 500 seires chip |
Range | Min 30m line of sight |
Relay | 15A (ON/OFF) |
Operating Temperature Range | 32-104°F (0-40°C) |
Dimensions | 115(L)*70(W)*44(H)mm |
Net weight | 130g |
Approval | Rohs,FCC, UL |
Z-wave frequency | 908.42MHz |
Installation1.Before installation ensure that the voltage supply is disconnected.IMPORTANT!Verify power is OFF to switch box before continuing.2.Remove wall plate.3.Remove the switch mounting screws.4.Carefully remove the switch from the switch box.DO NOT disconnect the wires.5.There are up to five screw terminals on the switch;These are markedA.LINE (Hot) - Black (connected to power)B.Neutral - WhiteC.LOAD - Black (connected to lighting)D.GROUND - Green/BareE.TRAVELER - Red/Other (only used in 3-way installations)Match these screw terminals to the wires connected to the existing switch.6.Disconnect the wires from the existing switch.Be careful to label wires according to thePrevious terminal connection.Observe Important Wiring InformationIMPORTANT!:This switch is rated for and intended to only be used withCopper wire.Wire Gauge RequirementsUse 14 AWG or larger wires suitable for at least 80° C for supplying Line (HOT), Load, Neutral,Ground and Traveler connections.Wire strip length:For attachment to screw terminals:Strip insulation 1" (25mm)For attachment using the enclosure's holes:Strip insulation 5/8" (16mm)UL specifies that the tightening torque for the screws is 14 Kgf-cm (12 lbf-in).7.Connect the green or bare copper ground wire to the GROUND terminal.8.Connect the black wire that goes to the fixture to the terminal marked LOAD.9.Connect the black wire that comes from the electrical service panel (Hot) to the terminalMarked LINE.10.Connect the white wire to the neutral terminal (use included jumper wire if needed).Note:The Traveler terminal is only used for 3-way or 4-way wiring and should remainInsulated if the switch is being installed in a 2-way system (one switch & one load).11.Insert Switch into the switch box being careful not to pinch or crush wires.12.Secure the switch to the box using the supplied screws.13.Mount the wall plate.14.Reapply power to the circuit at fuse box or circuit breaker and test the system.Basic OperationThe connected light can be turned ON/OFF in two ways:1.Manually from the front panel of the In-wall switch2.Remotely with a Z-Wave ControllerManual ControlThe Front Panel Toggle Switch allows the user to:Turn ON/OFF the connected fixture.To turn the connected fixture ON:Press and release up on the toggle.To turn the connected fixture OFF:Press and release down on the toggle.Adding your device to a Z-wave network:1.Follow the instructions for your Z-wave certified controller to include a device toThe Z-wave network.2.ZW31T:Quickly press ON (Up) or OFF (Down) button or three (3) times3.Once your controller has confirmed that the device has been included, refresh the Z-wave network to optimize performance.Please reference the controller's manual for instructions.Now you have complete control to turn your fixture ON/OFF or dimAccording to groups, scenes, schedules and interactive automationsProgrammed by your controller.If your Z-wave certified controller features Remote Access, you can now controlYour fixture from your mobile devices.To exclude and reset the device1.Follow the instructions for your Z-wave certified controller to exclude a device fromThe Z-wave network.2.ZW31T:Quickly press ON (Up) or OFF (Down) button or three (3) timesTo return your switch to factory defaults:ZW31T:Remove device from Gateway will restore factory mode.ZW31T:Support All On/All OffInvert SwitchIf the switch is accidentally installed upside down with "On" at thebottom and "Off" at the top, the default On/Off rocker settings canbe reversed by changing parameter 1's value to "1".? Parameter No: 1? Length: 1 Byte? Valid Values = 0 or 1 (default 0)Safety and maintenance instruction- Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.- Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.- Keep all parts away from young children's reach.- Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.- Avoid dropping or shocks, this can damage the electronic boards.- Never replace damaged power cables yourself!In such case, remove them from the net and take the devices to a workshop.- Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation.MaintenanceThe devices are maintenance-free, so never open them.The guarantee becomes void when you open the appliance.Only clean the outside of the devices with a soft, dry cloth or a brush.Prior to cleaning, remove the devices from all voltage sources.NOTEDo not use any carboxylic cleaning agents or petrol, alcohol or similar.These will attack the surface of devices.Besides, the vapors are hazardous to your health and explosive.Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning.Warranty 1 year
Adres:
Dongguan, Guangdong, China
Soort bedrijf:
Fabrikant/fabriek
Zakelijk Bereik:
Consument Elektronica's, Diensten, Elektrotechniek & Elektronica's, Instrumenten & Meters, Licht & Verlichting, Lichte Industrie & Dagelijks Gebruik, Produceren & Verwerken Machine, Veiligheid & Bescherming
Certificering Van Managementsysteem:
ISO 9001
Bedrijfsintroductie:
NIE-TECH Co., Ltd opgericht in 2009, is een Hi-tech fabrikant die gespecialiseerd is in het ontwerp, de ontwikkeling en de productie van slimme thuisproducten.
We bezitten het ervaren en innovatieve R&D-team en hebben een volledig assortiment succesvolle Z-Wave-oplossingen voor zowel thuis- als industriële toepassingen. Ons brede assortiment draadloze technologieën, dat ons veel vertrouwen heeft opgeleverd van onze klanten voor hun betrouwbaarheid en prestaties, helpen onze klanten hun innovatieve ideeën om te zetten in succesvolle producten.
Onze ZE300 Evalogik Gateway is het zenuwcentrum van slimme thuishaven. Met deze functie kunt u toegang krijgen tot en verschillende apparaten in uw huis bedienen met behulp van uw smartphone. De E300 Evalogik-gateway die op afstand kan worden bediend, varieert van verlichting, sensoren, gordijnmotoren, beveiligingscamera′s en energieregeleenheden. U hoeft alleen maar de gateway te configureren met het Wi-Fi-netwerk van uw huis en de EVALOGIK-APP op uw smartphone te installeren. U kunt dan alle apparaten toevoegen en aansluiten die compatibel zijn met de EVALOGIK-gateway.
Met het doel van "kwaliteit eerst, klant eerst" zorgt ons QC-team ervoor dat de producten gekwalificeerd zijn voordat ze worden verzonden. Lage kosten, korte tijd, hoge kwaliteit en onze strenge werkhouding helpen ons allemaal om meer orders te krijgen.
Hoe dan ook, ik kijk ernaar uit om in alle termen met u als biz-partner samen te werken.