Basis Informatie.
The Number of Rows
Single
Spherical
Non-Aligning Bearings
Load Direction
Radial Bearing
Material
Low Carbon Steel
Beschrijving
Descriptions
R&B bearings will support you to spot the difference in the example of HF 101612 and FC 10 as follows:
1: HF is flat end needle roller; while FC is pointed end needle roller;
2: HF is light series, while FC is heavy duty series one way bearing. It means FC will have higher torque rating than HF, which is the most important factor for one way bearing.
3: There is only one needle roller in each cage window for HF one way bearing; while multi-roller in each cage window for FC one way bearing.
4: Single roller per stainless steel spring for HF one way bearing; while multi-roller per stainless steel spring for FC one way bearing.
one-way needle roller bearing
HFL series drawn cup one-way needle roller bearing has two supporting needle bearing and one roller clutch which shares a punching outer ring, and can be used as a special space-saving support. The two supporting bearing are assembled on both sides of the roller clutch, and endure the radial load. The supporting needle bearing is composed of plastic cage and needles.
Main features: the unidirectional movement, reverse lock; the high conversion frequency and high conversion accuracy.
SPECIAL NOTES
? HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
? Plastic springs (HFL...KF) are available for some sizes.
? Partially knurled outer ring (HFL...R) is available upon request.
? A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
? Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
? The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
? The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
Specification:
Fw=inner diameter D=outer diameter C=height
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Suitable Drawn Cup Bearings |
Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 |
mm | g | mm | Nm | rpm |
HF ( / ) |
3 | HF0306KF | | 0.9 | 3 | 6.5 | 6 | 0.2 | 36000 | 7000 | HK0306TN |
4 | HF0406KF | -- | 1 | 4 | 8 | 6 | 0.34 | 34000 | 8000 | HK0408TN |
HF0406KFR | -- | 1 | 4 | 8 | 6 | 0.1 | 34000 | 8000 | HK0408TN |
6 | HF0608KF | | 2.8 | 6 | 10 | 8 | 1.5 | 20000 | 11000 | HK0608 |
HF0612KF | HF0612 | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 |
HF0612KFR | HF0612R | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 |
| HF061210 | 3.5 | 6 | 12 | 10 | 3 | 20000 | 13000 | HK061208 |
8 | HF0812KF | HF0812 | 3.5 | 8 | 12 | 12 | 3.15 | 17000 | 12000 | HK0808 |
HF0812KFR | HF0812R | 3.5 | 8 | 12 | 12 | 4 | 17000 | 12000 | HK0808 |
-- | HF061210 | 3.2 | 8 | 12 | 10 | 3 | 16000 | 12000 | HK0808 |
-- | HF081410 | 3.6 | 8 | 14 | 10 | 4.6 | 15000 | 11000 | HK081410 |
-- | HF081610 | 4.1 | 8 | 16 | 10 | 5.5 | 15000 | 11000 | HK081610 |
-- | HF081412 | 4 | 8 | 14 | 12 | 5 | 16000 | 12000 | HK081410 |
10 | HF1012KF | HF1012 | 4 | 10 | 14 | 12 | 5.3 | 14000 | 11000 | HK1010 |
HF1012KFR | HF1012R | 4 | 10 | 14 | 12 | 1.5 | 14000 | 11000 | HK1010 |
12 | -- | HF1216 | 11 | 12 | 18 | 16 | 12.2 | 11000 | 8000 | HK1212 |
14 | -- | HF1416 | 13 | 14 | 20 | 16 | 17.3 | 9500 | 8000 | HK1412 |
16 | -- | HF1616 | 14 | 16 | 22 | 16 | 20.5 | 8500 | 7500 | HK1612 |
18 | -- | HF1816 | 16 | 18 | 24 | 16 | 24.1 | 7500 | 7500 | HK1812 |
20 | -- | HF2016 | 17 | 20 | 26 | 16 | 28.5 | 7000 | 6500 | HK2010 |
| | HF2216 | 25 | 22 | 28 | 16 | 32 | 6500 | 6000 | |
25 | -- | HF2520 | 30 | 25 | 32 | 20 | 66 | 5500 | 5500 | HK2512 |
| | HF273420 | 30 | 27 | 34 | 20 | 110 | | | |
| | HF404725 | 45 | 40 | 47 | 25 | 185 | | | |
| | HF485620 | 43 | 48 | 56 | 20 | 230 | | | |
| | HF586820 | 86 | 58 | 68 | 20 | 320 | | | |
30 | -- | HF3020 | 36 | 30 | 37 | 20 | 90 | 4500 | 4500 | HK3012 |
35 | -- | HF3520 | 40 | 35 | 42 | 20 | 121 | 3900 | 3900 | HK3512 |
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Suitable Drawn Cup Bearings | Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 | mm | g | mm | Nm | rpm | HF (/ ) | 3 | HF0306KF | | 0.9 | 3 | 6.5 | 6 | 0.2 | 36000 | 7000 | HK0306TN | 4 | HF0406KF | -- | 1 | 4 | 8 | 6 | 0.34 | 34000 | 8000 | HK0408TN | HF0406KFR | -- | 1 | 4 | 8 | 6 | 0.1 | 34000 | 8000 | HK0408TN | 6 | HF0608KF | | 2.8 | 6 | 10 | 8 | 1.5 | 20000 | 11000 | HK0608 | HF0612KF | HF0612 | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 | HF0612KFR | HF0612R | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 | | HF061210 | 3.5 | 6 | 12 | 10 | 3 | 20000 | 13000 | HK061208 | 8 | HF0812KF | HF0812 | 3.5 | 8 | 12 | 12 | 3.15 | 17000 | 12000 | HK0808 | HF0812KFR | HF0812R | 3.5 | 8 | 12 | 12 | 4 | 17000 | 12000 | HK0808 | -- | HF061210 | 3.2 | 8 | 12 | 10 | 3 | 16000 | 12000 | HK0808 | -- | HF081410 | 3.6 | 8 | 14 | 10 | 4.6 | 15000 | 11000 | HK081410 | -- | HF081610 | 4.1 | 8 | 16 | 10 | 5.5 | 15000 | 11000 | HK081610 | -- | HF081412 | 4 | 8 | 14 | 12 | 5 | 16000 | 12000 | HK081410 | 10 | HF1012KF | HF1012 | 4 | 10 | 14 | 12 | 5.3 | 14000 | 11000 | HK1010 | HF1012KFR | HF1012R | 4 | 10 | 14 | 12 | 1.5 | 14000 | 11000 | HK1010 | 12 | -- | HF1216 | 11 | 12 | 18 | 16 | 12.2 | 11000 | 8000 | HK1212 | 14 | -- | HF1416 | 13 | 14 | 20 | 16 | 17.3 | 9500 | 8000 | HK1412 | 16 | -- | HF1616 | 14 | 16 | 22 | 16 | 20.5 | 8500 | 7500 | HK1612 | 18 | -- | HF1816 | 16 | 18 | 24 | 16 | 24.1 | 7500 | 7500 | HK1812 | 20 | -- | HF2016 | 17 | 20 | 26 | 16 | 28.5 | 7000 | 6500 | HK2010 | | | HF2216 | 25 | 22 | 28 | 16 | 32 | 6500 | 6000 | | 25 | -- | HF2520 | 30 | 25 | 32 | 20 | 66 | 5500 | 5500 | HK2512 | | | HF273420 | 30 | 27 | 34 | 20 | 110 | | | | | | HF404725 | 45 | 40 | 47 | 25 | 185 | | | | | | HF485620 | 43 | 48 | 56 | 20 | 230 | | | | | | HF586820 | 86 | 58 | 68 | 20 | 320 | | | | 30 | -- | HF3020 | 36 | 30 | 37 | 20 | 90 | 4500 | 4500 | HK3012 | 35 | -- | HF3520 | 40 | 35 | 42 | 20 | 121 | 3900 | 3900 | HK3512 |
1:;KF,KF; 2:R;
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Basic Load Ratings | Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 | C | Co | KN | mm | g | mm | Nm | rpm | HFL ( / ) | 3 | HFL0308 | -- | 3 | 3 | 3.6 | 8 | 1 | -- | -- | -- | -- | 4 | HFL0408 | -- | 3.5 | 4 | 8 | 8 | 1.5 | -- | -- | -- | -- | 6 | HFL0615KF | HFK0615 | 4 | 6 | 10 | 15 | 1.76 | 23000 | 13000 | -- | -- | HFL0615KFR | HFL0615R | 4 | 6 | 10 | 15 | 0.5 | 23000 | 13000 | -- | -- | -- | HFL061012K | 5 | 6 | 10 | 12 | -- | 21000 | 12000 | -- | -- | 8 | -- | HFL081212K | 6 | 8 | 12 | 12 | -- | 20000 | 12000 | -- | -- | -- | HFL081412K | 7 | 8 | 14 | 12 | -- | 19000 | 12000 | -- | -- | HFL0822KF | HFL0822 | 7 | 8 | 12 | 22 | 3.15 | 17000 | 12000 | 4.05 | 4.15 | HFL0822KFR | HFL0822R | 7 | 8 | 12 | 22 | 1 | 17000 | 12000 | -- | -- | 10 | HFL1022KF | HFL1022 | 8 | 10 | 14 | 22 | 5.3 | 14000 | 11000 | 4.3 | 4.65 | HFL1022KFR | HFL1022R | 8 | 10 | 14 | 22 | 1.5 | 14000 | 11000 | -- | -- | 12 | -- | HFL1226 | 18 | 12 | 18 | 26 | 12.2 | 11000 | 8000 | 6.3 | 6.5 | 14 | -- | HFL1426 | 20 | 14 | 20 | 26 | 17.3 | 9500 | 8000 | 7.1 | 7.7 | 16 | -- | HFL1626 | 22 | 16 | 22 | 26 | 20.5 | 8500 | 7500 | 7.7 | 9 | 18 | -- | HFL1826 | 25 | 18 | 24 | 26 | 24.1 | 7500 | 7500 | 8.3 | 10.3 | 20 | -- | HFL2026 | 27 | 20 | 26 | 26 | 28.5 | 7000 | 6500 | 8.9 | 11.5 | 25 | -- | HFL2530 | 44 | 25 | 32 | 30 | 66 | 5500 | 5500 | 10.9 | 14.1 | 30 | -- | HFL3030 | 51 | 30 | 37 | 30 | 90 | 4500 | 4500 | 12.6 | 17.6 | 35 | -- | HFL3530 | 58 | 35 | 42 | 30 | 121 | 3900 | 3900 | 13 | 19.3 |
| | | Fw | D | C | | Torrington/ & NSK/ | FC4K | 1 | 4 | 8 | 6 | 0.34 | FC6 | 3 | 6 | 10 | 12 | 1.76 | FC6K | 3 | 6 | 10 | 12 | 1.76 | FC8 | 4 | 8 | 14 | 12 | 5.3 | FCL8K | 3.5 | 8 | 12 | 12 | 5 | FC10 | 4.8 | 10 | 16 | 12 | 6 | FCL10K | 4 | 10 | 14 | 12 | 5.3 | FC12 | 11 | 12 | 18 | 16 | 12.2 | FC14K | 13 | 14 | 20 | 16 | 17.3 | FC16 | 14 | 16 | 22 | 16 | 20.5 | FC20 | 17 | 20 | 26 | 16 | 28.5 | FC25 | 30 | 25 | 32 | 20 | 66 | FC30 | 36 | 30 | 37 | 20 | 90 | FC35 | 40 | 35 | 42 | 20 | 121 | FCB8 | 10 | 14 | 14 | 20 | 5 | FCB10 | 15 | 16 | 16 | 20 | 10 | FCB12 | 18 | 18 | 18 | 26 | 12.2 | FCB16 | 22 | 22 | 22 | 26 | 20.5 | FCB20 | 27 | 26 | 26 | 26 | 28.5 | FCB25 | 44 | 32 | 32 | 30 | 66 | FCB30 | 51 | 37 | 37 | 30 | 90 | FCB35 | 58 | 42 | 42 | 30 | 121 |
| | | Fw | D | C | | Torrington/ & NSK/ | RC02 | 2 | 3.175 | 7.15 | 6.35 | 1.5 | RC040708 | 3.5 | 6.35 | 11.112 | 12.7 | 1.9 | RC040708-FS | 3.5 | 6.35 | 11.112 | 12.7 | 1.9 | RC061008 | 4.7 | 9.525 | 15.875 | 12.7 | 4.83 | RC061008-FC | 4.7 | 9.525 | 15.875 | 12.7 | 4.83 | RC081208 | 9.2 | 12.7 | 19.05 | 12.7 | 7.9 | RC081208-FS | 9.2 | 12.7 | 19.05 | 12.7 | 7.9 | RC101410 | 14.5 | 15.875 | 22.225 | 15.88 | 15.4 | RC101410-FC | 14.5 | 15.875 | 22.225 | 15.88 | 15.4 | RC121610 | 17 | 19.05 | 25.4 | 15.88 | 20.9 | RC121610-FS | 17 | 19.05 | 25.4 | 15.88 | 20.9 | RC162110 | 16.2 | 25.4 | 33.338 | 15.88 | 45 | RC162110-FC | 16.2 | 25.4 | 33.338 | 15.88 | 45 | RCB061014 | 12 | 9.525 | 15.875 | 22.22 | 4.83 | RCB061014-FS | 12 | 9.525 | 15.875 | 22.22 | 4.83 | RCB081214 | 16 | 12.7 | 19.05 | 22.22 | 7.9 | RCB081214-FC | 16 | 12.7 | 19.05 | 22.22 | 7.9 | RCB101416 | 21.3 | 15.875 | 22.225 | 25.4 | 15.4 | RCB101416-FS | 21.3 | 15.875 | 22.225 | 25.4 | 15.4 | RCB121616 | 26.5 | 19.05 | 25.4 | 25.4 | 20.9 | RCB121616-FC | 26.5 | 19.05 | 25.4 | 25.4 | 20.9 | RCB162117 | 44.8 | 25.4 | 33.338 | 26.99 | 45 | RCB162117-FS | 44.8 | 25.4 | 33.338 | 26.99 | 45 |
shaft dia. d | boundary dimensions | torque capacity | Fw | D1 | D2 | B | A | mm | mm | N.m (.) | Kg.cm(.) | 4 | 4 | 8 | 8.4 | 6 | 2.6 | 0.08 | 0.82 | 4 | 8 | 8.4 | 6 | 2.6 | 0.15 | 1.53 | 6 | 6 | 10 | 10.4 | 8 | 2.8 | 0.25 | 2.55 | 6 | 10 | 10.4 | 8 | 2.8 | 0.44 | 4.49 | 6 | 10 | 10.4 | 8 | 2.8 | 0.44 | 4.49 | 6 | 10 | 10.4 | 12 | 2.8 | 0.88 | 8.98 | 8 | 8 | 12 | 12.4 | 9 | 2.6 | 0.49 | 5 | <, ;, TD align=middle> 8 | 12 | 12.4 | 9 | 2.6 | 0.88 | 8.98 | 8 | 14.2 | 15 | 12 | 3.6 | 1.18 | 12.04 | 8 | 14.2 | 15 | 12 | 3.6 | 1.96 | 20 | 8 | 14.2 | 15 | 12 | 3.6 | 1.96 | 20 | 8 | 14.2 | 15 | 14.5 | 3.6 | 2.65 | 27.04 | 10 | 10 | 16 | 17 | 10 | 5 | 1.18 | 12.04 | 10 | 16 | 17 | 10 | 5 | 1.96 | 20 | 10 | 16 | 17 | 12 | 5 | 1.37 | 13.98 | 10 | 16 | 17 | 12 | 5 | 2.35 | 23.98 | 10 | 16 | 17 | 12 | 5 | 2.35 | 23.98 | 12 | 12 | 18 | 19 | 16 | 5.1 | 6.28 | 64.08 |
(1).nA. (2),. ,-0mm~-0.25mm,. |
Parameter list of OWC needle roller bearing
Shaft Dia. | Model | Weight | Size(mm) | Driving Torque |
mm | g | Inner Dia. | Outer Dia. | Height | ( Nm ) |
4 | OWC 410 | 1.8 | 4 | 10 | 5.4 | 2.8 |
5 | OWC 511 | 2 | 5 | 11 | 5.4 | 3.5 |
6 | OWC 612 | 2.3 | 6 | 12 | 5.4 | 5.2 |
8 | OWC 814 | 2.8 | 8 | 14 | 5.4 | 6.1 |
10 | OWC 1016 | 3 | 10 | 16 | 5.4 | 9.5 |
4 | OWC 406 | 1.6 | 4 | 8 | 6 | 2.5 |
4 | OWC 408 | 1.8 | 4 | 8 | 8 | 3.1 |
6 | OWC 612-8.4 | 2.35 | 6 | 12 | 8.4 | 6.8 |
6 | OWC 61407 | 2.1 | 6 | 14 | 7 | 6.6 |
6 | OWC 720 | 2.5 | 6 | 12.7 | 7.5 | 7.3 |
6 | OWC 087 | 2.38 | 6 | 10.2 | 8 | 4.6 |
6 | OWC 178 | 3 | 6 | 10.2 | 15 | 7.3 |
8 | OWC 81607 | 2.6 | 8 | 16 | 7 | 7.5 |
8 | OWC 812 | 3 | 8 | 12.7 | 7.3 | 6.8 |
8 | OWC 816-5.5 | 3.5 | 8 | 16 | 5.5 | 8.2 |
8 | OWC 816-6.2 | 3.8 | 8 | 16 | 6.2 | 8.8 |
10 | OWC 1008 | 3.35 | 10 | 16 | 8 | 9.7 |
10 | OWC 1019 | 8.5 | 10 | 19 | 11 | 19.8 |
17 | OWC 173512 | 22.5 | 17 | 35 | 12 | 78 |
17 | OWC 173516 | 25.5 | 17 | 35 | 16 | 95 |
17 | OWC 203316 | 23 | 20 | 33 | 16 | 108 |
MARKS:NON-STANDARD CAN BE PRODUCED |
Transfer capability:
Under the conditions of using the recommended mounting tolerances, the maximum torque that can be transmitteddepends primarily on the design of the seat shell and the shaft (materials, strength, wall thickness). Only when thewall thickness of the seat shell and its material allowable stress certain requirements, the clutch can transfermoment Md.
Installation:
Should be used the assembly mandrel with Needle roller bearings, needle roller clutch pressure holing hole(installed). When the clutch side of the direction of the arrow relative to the shaft is rotated, the clutch will lock, andtherefore should be noted locking direction before installation.
Lubrication:
HF-drawn cup needle roller clutch in oil and grease lubrication. Lubricated with oil, however, before you can get thebest performance, the standard HF-Drawn Cup Clutch has been filled with lithium grease.
Performance test:
The technical requirements of the test method and the standard circle described with Needle roller bearingsdimensional inspection mandrel used nominal size to take the tolerance zone as the lower limit for the h5 shaftalong the arrow in the opposite direction in the clutch can be locked.
Mounting tolerances:
The technical requirements of the seat shell HF-Needle roller bearings, the axis of the tolerance zone h5, the surfaceroughness Ra0.2m, not less than the hardness of HRC60.
Operating temperature:
HF-drawn cup needle roller clutch lubrication properly can the temperature range of -30 ° C to +120 °C long-running,short-term up to 150 ° C Operating Temperature. Lithium Grease Run
ONE WAY BEARING APPLICATIONS
Paper moving for copiers, fax machines, paper towel dispensers, etc.
Exercise equipment
Appliances
Two-speed gearboxes
Rack indexing drives
Converters, non-return devices and transcendental clutches.
Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
Adres:
Changhong West Road 182, Wujin District, Changzhou, Jiangsu, China
Soort bedrijf:
Fabrikant/fabriek
Zakelijk Bereik:
Auto Parts, Ijzerwaren & Gereedschap, Industriële Apparaturen & Onderdelen, Metallurgische, Mineralen & Energie, Produceren & Verwerken Machine
Certificering Van Managementsysteem:
ISO 9001
Bedrijfsintroductie:
Changzhou Lisongtai Industrial Motion Technology Co., Ltd, is een fabrikant gespecialiseerd in het produceren van diverse eenrichtingslagers, eenrichtingskoppeling, vrijloopkoppeling, naaldlagers. Meer dan 2000 standaardmodel van eenrichtingsdrager meer dan 1000 benamingen van metrische en inch-serie naaldlagers worden regelmatig geproduceerd en gebruikt voor motorfietsen, elektrisch en door de lucht aangedreven gereedschappen, printers, lichte en textielindustrie, machines, bouwmachines, auto′s Trucks en kantoorapparatuur in binnenlandse en wereldwijde markten. Bovendien worden er speciale lagers geleverd in overeenstemming met de eisen van de klant voor diverse toepassingen. We hebben onze producten geëxporteerd naar Korea, Iran, Turkije, Bulgarije, Roemenië, Rusland, Italië, Noorwegen, de VS, Canada, Wat
zijn wij?
Onze fabriek was gevestigd in de economisch ontwikkelde kuststad-industriewijk-Wujin Changzhou stad Jiangsu provincie. Hier is het vervoer handig, het zal slechts een uur naar Shanghai met de trein.
Wat wordt het hoofdproduct geproduceerd?
Eenweglagers, eenwegkoppeling, vrijloopkoppeling, tegenaanslagen, nokkenkoppeling, Naaldlager, steunrol en krommingslagers, cilindrische rollagers. Druklagers met een valse zitting. We hebben grote voorraden, en we accpecteren ook productie voor niet-standaard producten, tekeningen of monsters van klanten.
Wat is ons voordeel?
Product: In 1999 begon onze baas als ingenieur eenrichtingslagers te ontwikkelen en ontwerpen toen hij in een grote lagerfabriek werkte. Tot nu toe hebben we successen bij de ontwikkeling van de BB-serie, de MZ-serie, de TFS-serie, de NSS-serie RSBW-serie, die, om bevestigd te worden, een hoog kwaliteitsniveau bereiken dat vergeleken kan worden met het merk Tsubaki van Janpan.
Quliaty equivalent aan Stieber-koppeling, GVN-koppeling, Ringspann-koppeling, Formsprag-koppeling, NSK-koppeling, ect.
GFR-serie, DC-serie, ASNU-serie, NFR-serie, GFK-serie, NF-serie, AE-serie, AA-serie, ECT, die nog bevestigd moet worden, bereiken in een hoog kwaliteitsniveau kan worden vergeleken met HET MERK STIEBER uit het Duits.
FE-serie, FP-serie, FND-serie, FKN-serie eenwegkoppelingslager, dat, om te bevestigen, een hoog kwaliteitsniveau bereikt, kan worden vergeleken met het GVN-merk uit Duitsland.
Onze klanten de hoogste servicestandaard in onze branche blijven bieden. Het is onze bedoeling om voorop te blijven lopen op het gebied van het leveren en ontwerpen van lagers en om onze ontwikkeling naar nieuwe factoren voort te zetten.
Fabrieksapparatuur: Het bedrijf bezit de meest geavanceerde CNC automatische productielijn, automatische assemblagelijn en een verscheidenheid aan testapparatuur. De lagers die we hebben vervaardigd zijn allemaal laag geluidsniveau, lage vibratie, lage wrijving, hoge precisie, hoge afdichting, hoge draaisnelheid en lange levensduur.
Quantility control: 2011 we hebben de ISO9001: 2008 kwaliteitsmanagement systeem certificering gekregen, , al onze producten worden verstuurd voor meerdere malen inspectie. We leveren ook gedetailleerde tekeningen en bieden waar nodig aan.
Wat is de toepassing?
Wordt veel gebruikt in transportmachines, reduceermachines, hijsmachines, liften, auto′s, huishoudelijke apparaten, textielmachines, drukmachines, voedselmachines en mijnmachines, etc.
waar zijn onze producten gezouten?
Onze producten over de hele wereld spelen een belangrijke rol
in Duitsland, Groot-Brittannië, Nederland, Spanje, Italië,
In Indiaas, Indonesië, de Filipijnen, Thailand,
in Iran, Dubai
in Mexico moet
in de Verenigde Staten „Quality and Service” uw belangrijkste zorgen zijn die we in de praktijk hebben gebracht. Blader door onze productcategorie en laat ons uw vragen weten. Ons doel is om onze klanten te voorzien van goede kwaliteit en de beste concurrerende prijzen. Met voldoende voorraad, grote voorraad en handig transport verwelkomen we nieuwe klanten van harte om ons te bezoeken.